StudyVault
Home Unit Overview Revision Techniques Previous Lesson Next Lesson

Back to Home

Page tint:
0:00 / 0:00

Processing, Presenting and Analysing Data

This lesson covers the general fieldwork skills, terminology and exam expectations that apply to every student. The specific sites, data and methods your class actually used will be different — for the enquiry you’ll write about in the exam, refer to your teacher’s notes and the data you collected on the day.

From Raw Data to Evidence

When you come back from the field, your data sheets are full of tallies, counts and measurements. On their own they prove nothing. The next stages of the enquiry process turn those numbers into evidence. First you process the data. Then you present it. Finally you analyse it and link what you find to wider geography.

Processing means doing simple calculations so the data can be compared. The specification names two calculations you must be able to do: percentages and the mean. Presenting means showing the processed data as a map, graph or diagram so a reader can see the pattern quickly.

Key Fact

A percentage shows part of a total out of 100. A mean is the total of all values divided by the number of values. Both let you compare sites or groups fairly, even when sample sizes are different.

Percentages and Means

Percentages are useful for questionnaire and count data. Imagine 18 out of 60 shoppers you surveyed said they arrived by car. The calculation is \(\frac{18}{60} \times 100 = 30\%\). Turning counts into percentages matters when groups are different sizes. Saying “30% of shoppers” is fairer than saying “18 shoppers” if you interviewed more people at one site than another.

The mean summarises a set of measurements with one figure. Say you measured river width five times at one site: 2.1 m, 2.4 m, 2.6 m, 2.9 m and 3.0 m. Add them to get 13.0 m, then divide by 5. The mean width is 2.6 m. Using a mean of several readings is more reliable than trusting a single measurement. Be careful, though. One extreme value can drag the mean up or down, so always check for odd readings first.

Presenting: Choosing the Right Graph or Map

The golden rule is simple: match the presentation method to the type of data. A good choice makes the pattern obvious. A poor choice hides it. In the fieldwork paper you may be asked not just to draw a graph but to justify why it suits the data.

Key Fact

Categories = bar chart or pie chart. Change over time = line graph, such as a hydrograph. Two linked variables = scatter graph. Data grouped in equal class intervals = histogram. Patterns across places = choropleth, proportional circles or flow-line maps.

Bar charts compare totals in separate categories, such as the number of each type of shop in a street. Pie charts show parts of a whole, such as the percentage of people using each type of transport. They work best with only a few categories. Line graphs show continuous change, so climate charts and hydrographs use them.

Scatter graphs test whether two variables are linked, such as distance downstream and river width. A dispersion graph plots every value as a dot, so you can see whether readings cluster or spread out. It is a good way to compare two sites side by side. Histograms with equal class intervals show how often values fall into each band, such as pebble lengths in 10 mm groups.

A choropleth map shades whole areas, with darker shades for higher values. It shows patterns across neighbourhoods well, but it hides differences inside each shaded area. Proportional circles are drawn at points, with bigger circles for bigger values, such as pedestrian counts. Flow-line maps use arrows whose width shows the size of a movement, such as traffic or commuter flows.

Transect data needs its own methods. A kite diagram shows how plant cover changes along a line, for example through the zones of a sand dune. Cross sections show the shape of the land, such as relief across a river channel or the width and depth of an eroded footpath.

Referencing Secondary Data

Secondary data includes satellite images, aerial and oblique photographs, large databases such as National Statistics, and GIS sources such as Environment Agency flood maps. The specification says you must reference these sources accurately. That means naming who produced the data, what it is and when it was published or accessed. A reader should be able to find the same source and check your evidence. Without a reference, your evidence is much weaker.

Analysing Trends and Patterns

Analysis starts with describing what the data shows. State the overall direction, give figures and point out anything unusual. On a scatter graph, a rising pattern of points shows a positive correlation. A falling pattern shows a negative correlation. Points scattered randomly suggest no link. A strong answer might say: “Mean river width rises from 2.6 m at site 1 to 5.8 m at site 5.”

An anomaly is a value that breaks the pattern. Do not hide it. Ask why it happened. It could be a measuring mistake, or it could be real geography, such as a wide pool on a meander or a busy shop that pulls in pedestrians away from the centre.

Key Fact

Strong analysis has four parts: describe the pattern, quote figures from the data, identify any anomalies, and explain the pattern using a geographical process or concept.

Rivers. If pebbles get smaller and rounder downstream, link this to attrition. Pebbles knock against each other as they are transported, wearing them down. If width and discharge increase downstream, link this to tributaries adding more water.

Coasts. If sediment size changes steadily along a beach, link this to longshore drift moving material in one direction along the coast.

Urban areas. If pedestrian flows are highest in the centre, link this to the Central Business District and pedestrianised zones, where shops and services are concentrated. A busy count far from the centre might be explained by parking provision nearby.

The specification reminds you that geography can be ‘messy’. Fieldwork does not always match the expected outcome. Explaining why your results differ from the theory shows better understanding than pretending they fit perfectly.

Justifying Your Choices

A strong answer explains why a method suits the data and admits its limits. For example, proportional circles make differences between count sites easy to see, but large circles can overlap on a busy map. A pie chart clearly shows parts of a whole, but it becomes hard to read with many small segments. Naming a strength and a weakness shows you are thinking like a geographer.

Before moving on to conclusions, check three things. Have you processed the data fairly, using percentages or means? Does your presentation method match the data type? Have you described the pattern with figures and anomalies, and linked it to a process? If so, your analysis is ready to support a strong conclusion.

Exam question

AI feedback
This is a guide, not an exam mark. If your teacher marks it differently, go with your teacher.

Next lesson Back to unit
Explainer