River Processes and Landforms
From Source to Mouth
A river starts in the hills as a thin, fast trickle and ends at the coast as a wide, slow channel. Along the way it carves valleys, rolls boulders, sorts sand and drops silt. Geographers split this work into three jobs: erosion, transport and deposition. Different jobs dominate in different parts of the river’s course. That is why the landforms change as you travel downstream.
River landscapes are not made by water alone. River processes work together with weathering, mass movement and human activity to create the distinctive river landscapes of the UK. This lesson follows the River Tees, which rises high in the North Pennines and reaches the North Sea at Teesside. It is a useful example because it shows almost every landform you need to know.
Four Ways a River Erodes
A river erodes its bed and banks in four ways. Two are physical forces, one is the load wearing itself down, and one is chemical. You need to name each one and say what it does.
Rivers erode in four ways: hydraulic action (the force of the water forces air into cracks and breaks rock apart), abrasion (the load scrapes and grinds the bed and banks), attrition (stones knock together and become smaller and rounder) and solution (slightly acidic water dissolves rock such as limestone).
Do not mix up erosion with weathering. Weathering breaks rock down where it sits, for example through freeze-thaw on a valley side. Mass movement is the slipping or sliding of that loosened material downslope under gravity. Erosion is the wearing away done by the moving river itself. In a river valley all three work as a team: weathering loosens the valley sides, mass movement delivers material to the channel, and the river carries it away.
Four Ways a River Transports Its Load
Every river carries material, called its load. There are four ways to move it. Traction rolls large boulders along the bed. Saltation bounces smaller pebbles along in short hops. Suspension carries fine clay and silt within the water, giving it a brown, cloudy colour. Solution carries dissolved minerals that you cannot see. Notice that solution appears in both lists: it is a way of eroding and a way of transporting.
What a river can carry depends on its energy. Energy comes from gradient (how steep the slope is) and discharge (how much water flows past each second). When energy falls, for example on a gentle slope, on the inside of a bend or where the river meets the sea, the river starts to deposit. It drops the heaviest material first and carries the finest silt furthest.
Upper Course — Cutting Down
In the uplands the river is small but steep. Most of its energy goes into cutting downwards, which is called vertical erosion. Hydraulic action and abrasion grind a narrow channel into the bed. Meanwhile, weathering loosens the valley sides and mass movement carries this material down into the river. The result is a narrow, steep-sided V-shaped valley. The upper Tees in the North Pennines is a good example.
A waterfall forms where a river flows over a band of hard rock lying on top of softer rock. The softer rock erodes faster, so a step develops. Falling water uses hydraulic action and abrasion to drill a deep plunge pool at the base. The soft rock behind the falls is eroded back, leaving the hard rock as an overhanging lip. Eventually the unsupported lip collapses, and the waterfall moves a little further upstream. Over thousands of years this happens again and again.
As the waterfall retreats, it leaves behind a gorge. At High Force on the River Tees, a hard layer of rock called the Whin Sill sits on top of softer rocks. The river plunges over the Whin Sill, and a long, steep-sided gorge stretches downstream of the falls as evidence of its retreat.
Middle Course — Bending Sideways
As the gradient becomes gentler, the river uses more of its energy to erode sideways. This is called lateral erosion. Small bends become exaggerated into meanders. Over time, meanders migrate sideways and downstream, widening the valley floor.
On a meander the fastest, deepest flow swings to the outside of the bend, eroding a steep river cliff. On the inside of the bend the water is slow and shallow, so it deposits sand and gravel as a gentle slip-off slope.
Erosion on the outer banks makes the neck of land between two bends narrower and narrower. During a flood, the river may cut straight through the neck, taking the shortest route. Deposition then seals off the old loop, leaving an ox-bow lake. With time it fills with sediment and plants, becoming a marshy crescent on the valley floor.
Lower Course — Spreading Out
Near the sea the river is wide, deep and carrying a lot of fine load. It flows across a broad floodplain. When the river overtops its banks, the water spreads out and slows down. It drops its coarser sediment close to the channel, building low ridges called levees, and carries fine silt further across the valley floor. Each flood adds a new layer, so the floodplain becomes flat and fertile.
An estuary is the tidal mouth of a river. Here the river meets the sea, and the tide flows in and out twice a day. When the incoming tide meets the outgoing river, the water slows almost to a stop. The river loses energy and deposits its fine suspended silt and clay.
At low tide these deposits are exposed as wide mudflats. Where plants colonise the higher mud, salt marsh develops. The Tees estuary at Teesside shows these features, alongside heavy industry and a busy port. This mix of natural and human features makes estuaries good places to study how people and processes interact.
How People Change River Landscapes
Very few UK rivers are untouched. People change rivers to store water, to help ships and to move water away quickly. Each change alters the river’s energy and load, so it also changes erosion and deposition further along the channel.
Reservoirs. A dam across a valley floods the land behind it to store water, as at Cow Green Reservoir in the upper Tees valley. The still water of a reservoir traps sediment. Below the dam, the river carries less load and its flow is more controlled. With less sediment to drop, the river may erode its bed and banks more, while floodplains downstream receive less fresh silt.
Dredging. Dredging removes sediment from the river bed. It deepens the channel so it can hold more water or let large ships through, which is why busy estuary ports are dredged. However, it destroys habitats on the bed, and the sediment often builds up again, so dredging has to be repeated.
Straightening. Channel straightening cuts through meanders to make a shorter route. Water flows away faster, which can reduce flooding locally. But faster water carries more energy downstream, which can increase erosion and flood risk further down. Natural landforms such as meanders, slip-off slopes and ox-bow lakes are lost from the straightened stretch.
Human activity can slow down or speed up natural river processes. Reservoirs trap sediment, dredging deepens channels, and straightening speeds up flow. Each change shifts where erosion and deposition happen, often moving the problem further downstream.
Erosion, transport and deposition pass material along like a relay. A boulder loosened in the upper course is broken into pebbles by attrition, carried as silt in the lower course, and finally dropped on a floodplain or in an estuary. The landforms you have met — V-shaped valleys, waterfalls, gorges, meanders, ox-bow lakes, floodplains and estuaries — are the visible record of that journey. Human activity now edits that record in almost every UK river.